Short answer: For Somfy pergola control, order the Pergola 12V/24V 2-motor RTS Receiver & Antenna Kit (1870488). It drives two Pergola Tilt louver motors from RTS remotes and Somfy weather sensors, accepts 12V or 24V DC, caps each output at 3 A or 5.5 A, and ships with the Remote RTS Antenna (2400472) for installs that need the antenna away from the box.
The control box a louvered pergola needs
A louvered pergola roof tilts on linear actuators, and Somfy's Pergola Tilt motors take their commands from a control box. The Somfy Pergola 12V/24V 2-motor RTS Receiver & Antenna Kit (1870488) is the RTS box Somfy builds for that job. One receiver runs two motors on outputs S1 and S2, so a single box covers a roof with two louver banks or one long roof driven from both ends.
Somfy packs two parts in the kit. You get the Pergola 12V/24V 2-motor RTS Receiver (1870871) and the Remote RTS Antenna (2400472). From there the pergola joins the same RTS system that runs awnings, exterior screens and LED light kits, so one remote or one home automation interface can drive the whole patio.
Verified specs for the 1870488 kit
These figures come from Somfy's product page for ref 1870488 and its spec sheet D-0129.
| Somfy reference | 1870488 (receiver 1870871 plus Remote RTS Antenna 2400472) |
| Motors controlled | 2, on outputs S1 and S2 |
| Supply voltage | 12V or 24V DC |
| Output current | 3 A or 5.5 A per output, set on DIP switch 3 |
| Consumption | 45 W in operation, 0 W in standby |
| Radio | RTS, 433.420 MHz |
| Antenna | Built-in, plus the remote antenna in the kit |
| Protection index | IP 65 |
| Operating temperature | 14 to 140°F (-10 to 60°C) |
| Dimensions | 7.28 x 3.9 x 2.24 in (185 x 99 x 57 mm) |
| Limit setting | Fully automatic by default, semi-automatic option |
| Built-in sensor | Temperature |
| Warranty | 5 years |
Somfy adds overload and over current protection, plus obstacle detection to protect objects under the roof. Users can save a favorite "my" position between fully open and fully closed.
Motors and power: what the receiver fits
Somfy's product page lists the Somfy Pergola Tilt 24V 150mm Linear Motor (1230032) as the compatible motor, a 150 mm stroke actuator with a 2500 N nominal force. The spec sheet says the receiver supports motors with and without encoders, and DIP switch 1 tells the board which kind you wired. With switch 1 on, DIP switch 2 turns on synchronization between S1 and S2, which keeps two actuators on one roof moving together.
Power goes into terminals A (negative) and B (positive). Each motor lands on its own output, blue lead to negative and brown lead to positive: C and D for S1, E and F for S2. With Pergola Tilt 24V motors, run a 24V DC supply. Size it for both motors at the current limit you set on DIP switch 3, and check each motor's draw in the Pergola Motors spec sheet before you buy the supply.
Wind, rain, sun and ice inputs
The spec sheet names four sensors for this receiver: Eolis 24V, Ondeis 24V, Ondeis WireFree and Sunis Outdoor WireFree RTS. A wired Somfy Ondeis Rain Sensor 24V DC (9016344) lands on the rain sensor dry contact input, O for contact and P for common. The board also provides a 24 Vdc, 300 mA power output on terminals Q and R. Skip the wire run with the Somfy Ondeis WireFree RTS Rain & Sun Sensor (9019617), which pairs by radio.
Wind protection runs from an adjustable 12 to 60 mph trigger on the wind sensor. DIP switch 5 picks the response: on opens the louvers 50% in high wind, off opens them 100%. DIP switch 4 turns on the built-in temperature sensor, and the programming sequence below sets a separate snow and ice position for cold weather.
Read the status lights on the board to see which input held the roof. Orange shows a wind, rain or ice threshold. Red for 5 seconds means the board passed its current threshold or overheated during a command.
Programming steps Somfy publishes
Somfy's Pergola Tilt RTS Control Box quick guide (P-0036, October 2023) sets out this sequence. Cut power before you wire or change any wiring, and confirm the motor power plug sits fully inserted.
- Press and hold the PROG button on the circuit board until the S1 and S2 LEDs flash. The motor jogs.
- Briefly press PROG to select S1 or S2. The matching LED lights for the motor you are programming.
- On a multi-channel RTS remote, select the channel you want. Briefly press UP and DOWN together. The motor jogs.
- Press UP. If the pergola opens, the direction is correct. If it closes, press and hold MY until the motor jogs to reverse the direction.
- Briefly press MY and DOWN together to start the self-learning end limit process. Let the drive finish its search without interrupting it.
- Run the louvers to the snow and ice position with UP or DOWN, then press and hold MY until the motor jogs.
- Briefly press the PROG button on the back of the remote. The motor jogs, and the remote is paired.
- For the second motor, repeat steps 2 through 6.
To clear the box back to factory mode, hold PROG on the circuit board for more than 7 seconds until the indicator lights come on. Somfy publishes separate quick guides for its slim pergola motor and for encoder motors in semi-automatic mode, so match the guide to the motor on your roof. Our Somfy spec and install guide library holds the current versions.
Kit or receiver only
Order the 1870488 kit for a new pergola, or for any install where the receiver mounts inside the frame and the radio signal needs a clearer path. The quick guide wires the external antenna to terminal S for the signal conductor and terminal T for the ground shielding braid.
For a replacement board on a pergola that already has its antenna in place, the Somfy Pergola 12V/24V 2-motor RTS Receiver (1871434) covers two motors at 12V or 24V DC without the antenna.
Next parts for the pergola
Most pergola jobs pair this receiver with a 24V Pergola Tilt motor, one RTS remote and at least one weather sensor. Browse the full range of Somfy receivers and interfaces for lighting and automation add-ons. Our Pergola Tilt 24V 150mm motor guide covers the actuator side, and the RTS receiver guide compares this box with Somfy's universal and DC receivers.
Sources: Somfy product page for ref 1870488 (somfysystems.com); Somfy spec sheet D-0129, Pergola 12V/24V 2-motor RTS Receiver & Antenna Kit (10/2020); Somfy Pergola Tilt RTS Control Box quick guide P-0036 (October 2023).
FAQ
Does the Somfy 1870488 control two pergola motors?
Yes. The receiver has two drive outputs, S1 and S2, and Somfy built it to add RTS control to two pergola tilt motors. You program each motor on its own by selecting S1 or S2 with the PROG button, and DIP switch 2 can synchronize the pair when both motors carry encoders.
What voltage does the Somfy pergola receiver need?
Somfy rates the 1870488 receiver for 12V or 24V DC. Match the supply to your motors, so a pergola running Pergola Tilt 24V motors takes a 24V DC supply. DIP switch 3 limits each output to 3 A or 5.5 A, and the supply needs headroom for both motors at that setting.
Which sensors work with the Somfy pergola RTS receiver?
Somfy's spec sheet lists Eolis 24V for wind, Ondeis 24V and Ondeis WireFree for rain, and Sunis Outdoor WireFree RTS for sun. The wired Ondeis lands on the dry contact rain input, and the board offers a 24 Vdc, 300 mA power output beside it. A built-in temperature sensor handles ice protection.
What is the difference between 1870488 and 1871434?
The 1870488 kit pairs the pergola receiver with the Remote RTS Antenna (2400472). Ref 1871434 is the Pergola 12V/24V 2-motor RTS Receiver alone. Both run two tilt motors at 12V or 24V DC, so pick the kit for new installs and the receiver alone when an antenna is already mounted.
Shade Motors Direct is an authorized source for genuine Somfy motorized window shade, blind, and drapery parts.


