Skip to content
Genuine Somfy Motors & Parts for Roller Shades
Awnings

Somfy 12V Dimming LED RTS Receiver 1870607 for Awning Lights

Short answer: The Somfy Dimming LED RTS Receiver (1870607) is the 12V receiver inside Somfy's Dimmable LED RTS Light Kit. It runs on 120-230V AC, puts out up to 60 W of 12V DC, drives up to six Somfy LED bars, and dims across 12 brightness levels from the same RTS remotes and wall switches that run your awning or shade.

Somfy RTS 12V Dimming LED Control receiver 1870607 for dimmable 12V LED awning lights

Kit receiver or replacement: the decision this part settles

Somfy sells the Dimmable LED RTS Light Kit in two colors, Warm White (1811491) and Cool White (1811506). Each kit ships with one Dimming LED RTS receiver, a 5 ft and a 25 ft control-to-LED cable, and four 12V DC LED bars with adhesive tape. Somfy also lists the receiver on its own as part 1870607, so an installer can replace a failed unit or add a second lighting zone without buying a full kit.

The Somfy RTS 12V Dimming LED Control (1870607) is that stand-alone receiver. If the job already has Somfy 12V LED bars under an awning or pergola, this is the part that brings them back. If the job is new and you want 24V lighting with RGB options, the 24V receiver covered in our LED RTS 24V DC receiver guide belongs to a different system. The two run at different voltages, so keep each receiver with its own LED bars.

Awnings and pergolas the 1870607 lights

Somfy built the kit for outdoor living spaces: retractable awnings, pergolas and patio covers where the owner wants light under the fabric after sunset. The receiver takes line voltage in and sends 12V DC out to the LED bars over Somfy's interconnect cables. Each bar measures 3.3 ft by 0.75 in, carries 120 LEDs and draws 9.6 W at 12V DC. Warm White bars run at 3500 K and Cool White bars at 6500 K.

Six bars at 9.6 W come to 57.6 W, inside the 60 W output ceiling. That math sets the limit for one receiver. A run longer than about 20 ft of bar needs a second receiver and its own RTS channel.

Somfy's wiring example shows the receiver plugged into a Sunea awning motor, with both powered from the same source through the Sunea power cord. The receiver then rides along with the motor on one supply, which keeps the awning install tidy.

Verified specs

Somfy part number 1870607 (Dimming LED RTS receiver)
Power in 120-230V AC, 50-60Hz
Power out 12V DC, 60 W max (up to 6 Somfy LED bars)
Dimming 12 brightness levels, my button stores a favorite level
Radio RTS, 433.42 MHz
Maximum range 65 ft under optimal conditions
Receiver dimensions 12.39 x 2.30 x 1.63 in
Housing Polycarbonate
Operating temperature -4 to 104 F (-20 to 40 C)
Storage temperature -4 to 140 F (-20 to 60 C)
Kit rating IP 67 outdoor rated, UL Class 2 power supply
LED bar (kit) 3.3 ft x 0.75 in, 120 LEDs, 9.6 W at 12V DC
Warranty 5 years

What it fits: LED bars, cables and power

The receiver connects to the bars through Somfy's male and female LED connectors, so the system stays plug and play with no electrician needed for the low-voltage side. Somfy publishes control-to-LED cables in 0.5 ft, 5 ft, 15 ft and 25 ft lengths, a 5 ft LED extension (9019977) and an LED splitter (9020276) for branching runs across a pergola.

On the line side, Somfy lists Fast Connect power cords in 10.4 ft, 18 ft and 24 ft lengths in the same parts list as the receiver. The Somfy 3 Wire Fast Connector Cable SJTW 3C with Plug, 10.4 ft (9020791) is the short version, and the 18 ft and 24 ft cords cover longer reaches to an outdoor outlet.

Skip 12V plug-in power supplies on this receiver. The 1870607 takes 120-230V AC and makes its own 12V DC output, so a wall-wart transformer has no place in the circuit.

Control path: remotes, switches and app

Somfy rates the receiver compatible with its full range of RTS hand-held remotes and wall switches, plus the myLink app. The light gets its own channel beside the awning, and Somfy uses the my position to store a preferred lighting level.

A single-zone patio pairs well with the Somfy Situo 1 Channel RTS Pure Remote (1870571) for the lights alone. If one remote should run the awning, the lights and a screen, the Somfy Telis 4 RTS Multi-Channel Patio Remote (1810645) gives each its own channel in a housing made for outdoor use.

Somfy Telis 4 RTS Patio remote 1810645 for controlling an awning and dimmable LED lights

For a fixed control by the patio door, the Somfy DecoFlex 1 Channel RTS Wireless Wall Switch (1810897) mounts without wiring and talks RTS to the receiver like a hand-held remote.

Install and setup notes

Plan the bar layout first. Count bars, add up the watts, and keep the total at 60 W or less per receiver. Then measure from the receiver location to the first bar and pick the control-to-LED cable length that reaches without a loop of slack in the awning box.

Somfy rates the receiver for -4 to 104 F in operation. A pergola beam in full afternoon sun can run hotter than the air around it, so mount the receiver in a shaded spot under the structure where you can.

Pairing follows the standard RTS process for a receiver. Somfy's instructions for the specific remote you use are the reference, and our guide to pairing, adding and deleting a Somfy RTS remote covers the remote side. Keep the receiver within the 65 ft range of the remote, and less where walls or the awning cassette sit in the path. Install documents for each part live in the Somfy spec library.

Order the receiver, then add control

For a dead receiver on an existing Somfy 12V light kit, the Somfy RTS 12V Dimming LED Control (1870607) is the direct replacement. Pair it with a remote or wall switch and the lights dim on the same RTS channel plan as the awning. Browse the full range of Somfy RTS receivers and interfaces for lighting, dry contact and motor control, or compare it with the 24V system in our LED awning light kit guide.

FAQ

What does the Somfy 1870607 receiver do?

It adds RTS dimming to Somfy 12V LED bars. The receiver takes 120-230V AC, outputs up to 60 W of 12V DC and dims across 12 levels. It is the receiver Somfy packs into the Dimmable LED RTS Light Kit in Warm White (1811491) and Cool White (1811506), sold here on its own for replacements and added zones.

How many LED bars can one receiver run?

Somfy rates one receiver for up to six of its LED bars. Each bar draws 9.6 W at 12V DC, so six bars come to 57.6 W against the 60 W output limit. Bars measure 3.3 ft each, which puts a single receiver at roughly 20 ft of light. Longer runs need a second receiver on its own channel.

Which remotes control the dimmable LED RTS light kit?

Somfy lists the receiver as compatible with its full range of RTS hand-held remotes and wall switches and with the myLink app. A Situo 1 RTS handles lights alone, a Telis 4 RTS Patio runs lights and awning on separate channels, and a DecoFlex RTS wall switch gives a fixed control by the door.

Can I use a 12V plug-in power supply with this receiver?

No. The 1870607 runs on 120-230V AC line voltage and creates its own 12V DC output for the LED bars, so it needs no external transformer. Somfy's wiring example powers the receiver from the same source as a Sunea awning motor through the motor's power cord, and Fast Connect power cords appear in its parts list.

Shade Motors Direct is an authorized source for genuine Somfy motorized window shade, blind, and drapery parts.

Sources: Somfy Dimmable LED RTS Light Kit spec sheet (12-2019, somfysystems.com / service.somfy.com), parts 1811491, 1811506 and 1870607.

Previous Post Next Post

Leave A Comment

Please note, comments need to be approved before they are published.

Welcome to our store
Welcome to our store
Welcome to our store