The Somfy Sonesse 506S2 PA Motor (1001801) solves a wiring problem before it solves a torque problem. Somfy builds this Sonesse 50 variant with a 12 cm stripped-end pigtail instead of a long cord, so the electrician terminates it in a junction box at the pocket. Installers who hard-wire shades into a switch leg pick this reference for that reason.
Tube diameter and head type decide this motor
Somfy publishes the Sonesse 506S2 PA as a 50 mm motor that needs a tube with at least 47 mm (1.85 in) of clear inside diameter. Overall length runs 616 mm, or 24.25 in. Measure the tube bore first, then measure the pocket depth. A 2 in profiled tube and a 2.5 in aluminum tube both clear 47 mm, and both take Somfy crowns from the LT50 range.
The head is a star. That single fact rules out every round-head bracket on the shelf. Somfy codes the motor 506S2 SONESSE PA 6/32 2464, where 6 gives torque in newton meters, 32 gives speed in rpm, and 2464 names the cable. The motor body measures 45 mm across the outside, which leaves clearance inside a 47 mm bore for the drive wheel to seat.
Shades and screens the 506S2 PA drives
Six newton meters at 32 rpm handles interior roller shades, solar screens, large roman shades and exterior sunscreens on a 2.5 in tube. Somfy rates the motor at 45 dB, quiet enough for a bedroom, a boardroom, a classroom or a hotel guest room. The limit unit holds 29 turns, which sets the real travel ceiling on a tall shade. Count wraps at the design stage. A 2 in tube with a heavy fabric eats turns faster than a 2.5 in tube does, and a screen can run out of turns long before it runs out of torque.
Commercial and hospitality jobs favor the PA variant. Designers specify it where the pocket has a junction box and the shade runs from a wall switch rather than a plug. Residential retrofits that need a cord and plug call for a different Sonesse 50 reference.
Verified Sonesse 506S2 PA specifications
| Somfy reference | 1001801 |
| Torque / speed | 6 Nm (53 in-lb) / 32 rpm |
| Power supply | 120V AC, 60Hz (108 V to 132 V) |
| Rated current | 1.2 A |
| Power consumption | 146 W running, 0 W standby |
| Minimum tube inside diameter | 47 mm (1.85 in) |
| Overall length | 616 mm (24.25 in) |
| Motor external diameter | 45 mm (1.77 in) |
| Head type | Star |
| Noise level | 45 dB |
| Limit switch | Mechanical progressive, 29 turns |
| Cable | Type 2464, 0.12 m, white, 4 conductor, stripped ends |
| Insulation class | Class I |
| Ingress protection | IP 44 |
| Thermal cut-out time | 4 minutes |
| Operating temperature | -20 C to 60 C |
| Weight | 2.25 kg |
| Warranty | 5 years |
Crowns, drives and brackets that fit
Build the drive train around the tube. A 2.5 in aluminum tube takes the Somfy LT50 2.5" Crown (9707026) at the idle end, where it carries the tube on the idler pin and keeps the shade running true. The motor end takes the Somfy LT50 2.5" Hard Clip Drive (9206019), which locks onto the star head and transmits torque into the tube wall. The hard clip grips a rigid aluminum wall. A thin-wall tube wants the soft clip version of the same drive.
The star head needs a plate built for a star. Use the Somfy Sonesse 50 Star Head Motor Bracket 55P (9014135) and fix it to the pocket wall or the window frame before you load the tube. Somfy also lists the LT50 universal star head bracket against this platform, rated to 50 Nm, which gives wide headroom over 6 Nm. Match the fixing centers to the pocket you have.
Skip 40 mm crowns and drives on this motor. They will not seat on a 50 mm body, and forcing one damages the tube wall.
Wiring a 12 cm pigtail
Somfy gives this reference four conductors in a 0.12 m white lead with stripped ends: one for up, one for down, a neutral and a ground. The lead reaches a junction box inside the pocket and no further. Add the Somfy Sonesse 50 and LT50/LT60 SJTW 4C Cable 10 ft (9018345) when the box sits away from the motor end, and splice inside an approved enclosure.

Class I insulation puts the ground wire to work, so bond it. Somfy rates the motor IP 44 and sets the thermal cut-out at 4 minutes, which covers a full travel cycle on a tall screen with margin to spare. The motor pulls 1.2 A and 146 W while it runs, then drops to 0 W at rest. Six of these motors on one 15 A circuit still leave headroom for the controller.
Control today, radio later
A maintained or momentary wall switch runs this motor straight out of the box. Somfy motor controllers and dry-contact outputs from a building system drive it the same way. The limits are mechanical and progressive, set at the head with a Somfy setting tool, so the shade keeps its stops through a power cut and needs no re-teaching.
No radio lives inside this motor. Installers who want remote or app control add an RTS or Zigbee receiver on the line side, then bring the shade into a TaHoma system alongside the rest of the house. That path keeps the wired motor and adds the control layer later, which suits a commercial fit-out where the automation package lands after the shades.
Order the Somfy Sonesse 506S2 PA Motor (1001801) with the crown and drive that match your tube, plus a star head bracket, and add the SJTW cable if the junction box sits outside the pocket.
Frequently asked questions
What tube does the Sonesse 506S2 PA need?
Somfy sets the minimum tube inside diameter at 47 mm, which is 1.85 in. A 2 in profiled roller tube and a 2.5 in aluminum tube both clear that bore. Pair the tube with an LT50 crown at the idle end and a matching clip drive on the star head.
Does the 506S2 PA include a power cord?
Somfy supplies a 0.12 m stripped-end pigtail with four conductors, not a cord and plug. An electrician wires it into a junction box or a switch leg. Add a 10 ft SJTW 4 conductor cable when the box sits away from the motor end of the tube.
How many turns does the limit switch hold?
The mechanical progressive limit unit holds 29 turns. Count the wraps your shade needs at the design stage, because fabric thickness and tube diameter both change the count. A tall screen on a 2 in tube can reach the turn limit while torque headroom remains.
Can I add remote control to a 506S2 PA?
Yes. The motor carries no built-in radio, so installers add an RTS or Zigbee receiver on the supply side. The receiver gives you handheld remotes, wall transmitters, timers and TaHoma app control while the motor stays wired.
Shade Motors Direct is an authorized source for genuine Somfy motorized window shade, blind, and drapery parts.


