
Somfy builds the LT60 6100R2 CMO for the awning that sits at the top of the torque chart and still has to come in by hand when the power drops. Ref 1166016 carries 100 Nm at 14 rpm and a Compact Manual Override head.
Torque first, then the tube
A 100 Nm motor earns its place on an awning the LT50 range cannot move. Somfy rates the 6100R2 CMO at 100 Nm and 14 rpm, the top torque in the LT60 wired line. Fabric weight, projection and roller tube diameter set that figure. An installer who measures the loaded pull on a wide lateral arm awning and lands past the 80 Nm 680R2 should order this ref instead of stacking two smaller motors.
The second measurement decides the order as much as the first. Somfy publishes a 2.37 in minimum tube inside diameter for this motor. Measure the inside of the tube, not the outside. A tube below that figure will not take the motor body and the crown together, and no bracket choice recovers the clearance.
Somfy lists awning and rolling shutter as the applications for ref 1166016. The 600 Series platform covers wide lateral arm awnings, large cassette awnings, storefront rolling shutters and heavy security shutters. Four wires carry the control, so the motor answers a wall switch, a relay or a building control panel rather than a radio remote.
Dealers reach for the CMO head when the shade has to move during an outage. A restaurant patio awning out over a deck on a windy evening with a dead circuit is the case the crank solves. The override shaft threads into the CMO head, a pole engages the shaft, and the operator rolls the fabric back in by hand. Somfy keeps the same override geometry across the LT50 and LT60 CMO motors, so a dealer who stocks crank poles already has the tool.
Verified specifications
| Reference | 1166016 (6100R2 CMO) |
| Torque / speed | 100 Nm / 14 rpm |
| Power supply | 120V AC, 60 Hz (108 V to 126 V) |
| Rated current | 3.8 A |
| Consumption | 430 W running, 0 W standby |
| Limit capacity | 34 turns |
| Head type | CMO (Compact Manual Override) |
| Cable | 2464, 4 wires, white, removable, 6.56 ft |
| Motor diameter | 2.36 in |
| Minimum tube inside diameter | 2.37 in |
| Overall length | 26.81 in |
| Weight | 11.97 lb |
| Sound level | 67 dB |
| Protection | IP 44, insulation class I |
| Thermal protection | Trip at 266 F, 4 min thermal time |
| Operating temperature | -13 F to 158 F |
| Storage temperature | -4 F to 176 F |
| Approval | UR |
| Warranty | 5 years |
Somfy prints the commercial code as 6100R2 100/14 CMO 2464 2M. The code packs the torque, the speed, the head style and the cable type into one string, and it is the fastest way to confirm a motor on the bench against a packing list.
Tube, crown and drive fit
The LT60 body runs 2.36 in across. A crown carries the motor inside the tube and a drive wheel transfers the torque to the tube wall, so the pair has to match the tube profile already on the awning. Somfy's accessory list for ref 1166016 names the 70mm Octagonal LT60 Crown and Drive Set 9012247 for 70mm octagonal tube, and it adds round sets at 2.5 in, 2.75 in, 3.5 in and 4.0 in for round profiles.
Count the turns before the fabric goes on. The limit switch holds 34 turns of travel. A 4.0 in tube takes in more fabric per turn than a 2.5 in tube, so a long projection on a narrow tube can run the count out before the awning reaches full extension. Larger tube, fewer turns, more reach.
Brackets on a CMO motor differ from the plain wired versions. The override shaft passes through the head, so the bracket has to clear it. Somfy publishes the CMO Awning Motor Bracket and the CMO ME Bracket against this ref for that reason. Confirm the bracket style against the head on the motor you receive before you drill the hood.
The override path

Somfy pairs ref 1166016 with the CMO Awning Override Shaft 9707287, a 100mm shaft with a Geiger eye. The shaft drops into the CMO head and gives the crank pole a point to engage. Somfy also publishes a 170mm version, ref 9685136, for installations where the bracket sits further off the wall and the 100mm shaft cannot reach past the hood.
Order the shaft with the motor. The motor arrives without it, and a crank pole has nothing to grip until the shaft goes in. Somfy's accessory list for this ref also carries hex extension shafts at 220mm and 330mm plus a 7mm hex connector sleeve, which cover the deep hoods and the corner runs where the pole cannot sit square to the head.
Wiring and limit setup
Somfy ships the 6100R2 CMO with a 2464 cable, 6.56 ft long, four wires in white, removable at the head. Two conductors drive the two directions, one is neutral and one is ground. A momentary rocker, a key switch or a relay output from a panel handles the control, and the removable cable lets an electrician pull the lead through conduit and seat the head after.
Somfy's Standard Motor Tester Cable 9012116 sits on the accessory list for this ref and shortens the bench work. Run the motor, set the limits and confirm direction before the tube goes into the hood. Somfy rates the mechanical limits at 34 turns and sets the thermal trip at 266 F with a 4 minute recovery, so back-to-back cycling on a commissioning day deserves a pause between runs.
Budget 3.8 A and 430 W per motor on the circuit. Standby draw sits at 0 W, which keeps a bank of shutters off the standby load calculation for a commercial panel. Insulation class I means the ground conductor carries a job, so terminate it.
Ordering the 6100R2 CMO
The Somfy LT60 6100R2 CMO 120V 4-Wire Motor (1166016) suits the large awning or storefront shutter that needs 100 Nm and a hand crank for outages. Somfy backs it with a 5 year warranty and an IP 44 rating, with an operating range from -13 F to 158 F for exterior mounting.
Pair it with the crown and drive set that matches your tube, the override shaft for the crank, and the tester cable for the bench. A dealer running a 60 Nm or 80 Nm job on the same platform can order the 660R2 or the 680R2 and keep the same crowns, drives and override hardware across the van.
FAQ
How much torque does the Somfy 6100R2 CMO produce?
Somfy rates ref 1166016 at 100 Nm at 14 rpm. That is the top torque in the LT60 wired line and covers wide lateral arm awnings, large cassette awnings and storefront rolling shutters. Fabric weight and tube diameter decide whether a job needs 100 Nm or drops to the 80 Nm 680R2.
What tube does the LT60 6100R2 CMO fit?
Somfy publishes a 2.37 in minimum tube inside diameter. The motor body measures 2.36 in across. Match a crown and drive set to the tube profile, such as the 70mm Octagonal LT60 set 9012247 for octagonal tube or a round set at 2.5 in through 4.0 in for round tube.
Which override shaft fits this motor?
Somfy lists the CMO Awning Override Shaft 9707287, a 100mm shaft with a Geiger eye, against ref 1166016. A 170mm version, ref 9685136, covers brackets that sit further from the wall. Hex extension shafts at 220mm and 330mm reach past deep hoods.
How do you wire the 6100R2 CMO?
The motor ships with a removable 2464 cable, 6.56 ft long, carrying four white wires: two directions, neutral and ground. A momentary rocker, key switch or relay output controls it. Allow 3.8 A and 430 W per motor on a 120V, 60 Hz circuit, and terminate the ground for insulation class I.
Shade Motors Direct is an authorized source for genuine Somfy motorized window shade, blind, and drapery parts.


