Awning fabric gets heavier the wider you go, and the Somfy Sunea 525A2 RTS CMO sits at the 25 Nm step of the Sunea ladder for that reason. Somfy builds this motor for cassette, semi-cassette and open awnings on a 50 mm tube. It carries radio control inside the motor and a hand crank socket on the head, so the awning still retracts when the power drops.

Awning width and fabric weight pick the torque
Somfy publishes 25 Nm at 20 rpm for reference 1114304. That pairing covers most residential cassette awnings in the 10 to 14 foot projection range once you account for the fabric, the front bar and the arm return springs. Installers who spec a 16 foot cassette or a heavy acrylic with a valance step up to the 535A2 or the 550R2 on the same platform. The speed matters as much as the torque on an awning. At 20 rpm the fabric rolls out at a pace the arms can follow without snatching, and the electronic limits hold the front bar square at the closed position.
Somfy lists one application for this reference: awning. The Sunea head sits inside a cassette housing, which is the point of the CMO version. Nothing protrudes past the end plate except the override socket.
The override is the reason to buy a CMO head
Compact Manual Override gives the awning a mechanical retract path. A hex shaft threads into the motor head, a crank or an eye hook connects to that shaft, and the user winds the awning in by hand. Storm warnings and power cuts arrive together often enough that a fixed awning stuck at full projection becomes an expensive repair. Somfy sizes the CMO shaft in two lengths, 100 mm and 170 mm, with and without a Geiger eye on the end.
Electronic limits on the Sunea reset themselves as the fabric settles over the first season. A new awning stretches. The motor relearns the closed point rather than driving the front bar into the cassette.
Verified specs for reference 1114304
| Somfy designation | SUNEA 50 RTS CMO 25/20+FC |
| Torque | 25 Nm |
| Speed | 20 rpm |
| Power supply | 120 V AC, 60 Hz |
| Rated current | 1.6 A |
| Standby consumption | 0 W |
| Minimum tube internal diameter | 1.85 in |
| Motor body external diameter | 1.77 in |
| Overall length | 28.35 in |
| Limit system | Electronic, 250 turn capacity |
| Head type | CMO (Compact Manual Override) |
| Cable | Removable 3-wire SJTW, white, Fast Connector ends |
| Radio | RTS, 433.420 MHz, rolling code |
| Channel memory | 12 |
| Range, open field | 656.2 ft |
| Noise level | 55 dB |
| Protection index | IP 44 |
| Insulation class | Class I |
| Thermal protection | 4 min |
| Operating temperature | -4 to 158 °F |
| Weight | 5.95 lb |
| Warranty | 5 years |
Figures come from Somfy's published data for reference 1114304.
Tube, crown, drive and bracket fit
The motor body measures 1.77 in across and needs a tube with at least 1.85 in of internal clearance. Awning tubes in this class run 60 mm octagonal, 70 mm octagonal and 2.5 in round, and each profile takes its own crown and drive pair. Match the drive to the tube profile first, then confirm the crown seats against the motor head without a gap.
Somfy names the 2.5 in soft clip LT50 drive, 9206041 for this reference, along with the octagonal sets in 60 mm and 70 mm. The soft clip version holds a thin-wall round tube without crushing it. Installers running 70 mm octagonal awning tube pick the matching octagonal set instead. Tube internal diameter settles the choice, not the tube's outside measurement.
A Sunea CMO head takes a platform-specific bracket. The Sunea RTS CMO Universal Bracket, 9015802 carries the motor end inside a US cassette, and Somfy publishes a metric version of the same bracket for imported cassette systems. Both bolt the motor head so the override shaft lines up with the hole in the end plate.
For the crank side, the 100 mm CMO override shaft with Geiger eye, 9707287 drops into the head and gives the user a standard eye for a crank hook. Deeper cassettes call for the 170 mm shaft. Measure from the motor head face to the outside of the end plate before ordering, because a short shaft leaves the eye inside the housing where no one can reach it.
RTS control and pairing
Radio Technology Somfy lives inside the motor on this reference, which removes the control wiring run back to the head. The lead carries three conductors and terminates in a Fast Connector, so the electrician brings power to the motor and nothing else. The motor holds 12 transmitter channels and uses a rolling code, and Somfy rates the open field range at 656.2 ft.
Pairing takes a handheld transmitter. Press the programming button on the back of a paired remote until the awning jogs, then confirm on the new remote. The Situo 1 Channel RTS Pure remote handles a single awning. Larger sites add a Situo 5 for multiple awnings on one handset, or a TaHoma switch when the owner wants schedules, sun sensors and phone control over the same radio.
Wind protection deserves a thought at this stage. An Eolis 3D WireFree RTS sensor mounts on the front bar and retracts the awning when it reads movement, and it pairs into the same motor memory as the remote.
Install notes installers ask about
Set the closed limit with the fabric under tension rather than slack, because the front bar needs to pull up against the cassette seal. Leave the thermal cycle in mind during commissioning. The motor runs 4 minutes before the thermal cutout opens, which covers several full cycles on a 12 foot awning but not an afternoon of repeated testing.
Mount the motor so the cable exits toward the wall side and the override socket faces the crank position the owner will use. The head has one orientation inside the bracket. Getting it backward means pulling the tube again.
Shop the Somfy Sunea 525A2 CMO RTS motor, reference 1114304 and add the bracket, the drive and the override shaft that match your cassette and tube.

Frequently asked questions
What size awning does the Sunea 525A2 RTS CMO handle?
Somfy rates this reference at 25 Nm and 20 rpm, which suits most residential cassette awnings in the 10 to 14 foot projection class once the fabric, front bar and arm springs are counted. Heavier acrylic fabric, a valance or a wider cassette moves the pick up to the 535A2 or 550R2 on the same Sunea platform.
Which tube does this motor fit?
The motor body measures 1.77 in across and needs a tube with 1.85 in of minimum internal diameter. Somfy lists 60 mm octagonal, 70 mm octagonal and 2.5 in round crown and drive sets against this reference. Measure the inside of your tube, then pick the crown and drive pair for that profile.
How does the manual override work during a power outage?
A hex shaft threads into the CMO head and passes through the cassette end plate. The user hooks a crank onto the eye on that shaft and winds the awning closed by hand. Somfy supplies the shaft in 100 mm and 170 mm lengths, with and without a Geiger eye, so the cassette depth decides which one you order.
Does the motor need control wiring back to a switch?
No. RTS sits inside the motor, so the installation needs power only. The 3-wire SJTW lead ends in a Fast Connector, and control arrives over 433.420 MHz radio from a Situo or Telis handheld, a DecoFlex wall transmitter or a TaHoma switch. The motor stores 12 transmitter channels.
Shade Motors Direct is an authorized source for genuine Somfy motorized window shade, blind, and drapery parts.


