Skip to content
Genuine Somfy Motors & Parts for Roller Shades
Awning Motors

Somfy 540R2 CMO 40 Nm LT50 Motor Fit and Torque Guide

Somfy 540R2 CMO 40 Nm LT50 tubular motor for awnings and rolling shutters

A 540R2 CMO needs a roller tube with at least 1.85 inches of inside diameter. Measure that tube before you weigh torque figures against each other, because the 1.77 inch motor body and the crown that carries it have to clear the inner wall. Somfy builds this motor for exterior work, and it carries a compact manual override so the owner keeps a crank when the power drops. Shade Motors Direct stocks it as the Somfy 540R2 CMO 120V 4-Wire Motor (1049026).

Torque and speed the 540R2 CMO brings to a tube

Somfy publishes this motor at 40 Nm and 14 rpm. That pairing suits a heavy load that you want moved under control rather than fast. A wide retractable awning with a heavy valance, a commercial rolling shutter on an aluminum curtain, an exterior screen on a tall opening: all three land inside the band this motor was built for.

Specify torque from the weight the tube carries and the diameter it rolls onto, never from the opening width alone. A fabric awning on a 70 mm tube asks less of the motor than a slatted shutter curtain of the same width on the same tube. The 14 rpm figure sets the travel time. Count the turns your application needs and check them against the limit switch capacity of 34 turns, because that number caps the travel this motor can learn.

Somfy rates the motor at 210 W while it runs and 0 W at rest. Size the circuit from the running figure when several motors share a feed.

Awnings and rolling shutters this motor was built to run

Somfy lists awning and rolling shutter as the applications for reference 1049026. The CMO head is the reason installers reach for it on an awning. A folding arm awning on a patio stays usable through an outage, because the owner hooks an eye rod into the override and winds the fabric back in before weather reaches it. The same logic covers a rolling shutter over a storefront, where a shutter stuck open after a power cut leaves the glass exposed.

The motor runs on 120V AC at 60 Hz, inside a declared range of 108 V to 126 V, and carries an IP 44 rating with UR approval. IP 44 covers a motor that sits inside a tube in a hood or a cassette, protected from splashing water. Keep the head and the cable entry out of standing water and direct spray.

Verified specs for reference 1049026

Specification Published figure
Commercial code 540R2 40/14 CMO 2464 2M - UN
Torque 40 Nm
Rotation speed 14 rpm
Power supply AC RGE 2, 120V / 60 Hz (108 V to 126 V)
Power consumption 210 W running, 0 W standby
Limit switch capacity 34 turns
Minimum tube inside diameter 1.85 in
Motor body diameter 1.77 in
Override Compact manual override (CMO)
Control Standard 4-wire, no radio receiver
Cable Type 2464, removable, 6.56 ft, 4 wires, white
Protection rating IP 44
Approval UR
Application Awning and rolling shutter
Warranty 5 years

Two figures in that table do the work on an order. The 1.85 inch minimum tube diameter decides whether the motor goes in at all. The 34 turn limit capacity decides whether it can learn the full travel of a tall shutter.

Crowns and drives that seat this motor in an LT50 tube

Somfy Octagonal LT50 70mm crown and drive set for 500 Series tubular motors

The motor carries no tube adaptation of its own. A crown locates the motor head end inside the tube and a drive transmits rotation to the tube wall, and both match the tube profile you ordered. Pick the pair from the tube, not from the motor.

For an octagonal shutter tube, the Somfy Octagonal LT50 60MM Crown/Drive Set (9012233) and the Somfy Octagonal LT50 70mm Crown and Drive Set (9012234) cover the two octagonal sizes this platform sees most. A 78 mm tube takes the Somfy LT50 DS78MM Crown/Drive Set (9012239). On a round 2.5 inch tube, the Somfy LT50 2.5" Hard Clip Drive (9206019) clips the drive to the tube wall and holds it against the torque this motor produces.

Order the crown and the drive together. A mismatched pair leaves the motor floating in the tube, and the tube then wears the drive teeth down over a season of cycles.

Wired control today, a radio receiver when the job needs one

The 540R2 CMO reads four wires and nothing else. Two wires call the two directions, one takes neutral, one takes ground, and a maintained wall switch or a Somfy motor controller sends the command. Nothing pairs, nothing holds a battery, and nothing loses its programming after an outage. Installers choose the wired head where the switch location was settled during framing and the conduit is already in the wall.

Radio control still reaches this motor later. An RTS or Zigbee receiver sits upstream on the supply side, and the motor sees switched power the way it always did. Plan the receiver into an accessible box at that point rather than inside a sealed awning hood, because a receiver you can reach is a receiver you can re-pair.

Setting limits and wiring the crank

Set the two mechanical end limits on the motor head with the supplied adjustment key before you load the fabric or the curtain. Run the tube to the closed position, dial the limit in, then repeat at the open end and cycle the motor four times to confirm both stops hold.

The CMO input takes an eye rod or an override shaft on the head end, and it needs clearance outside the tube. Lay out the hood or the cassette so the crank entry stays reachable after the fascia goes on. An override you have to dismantle a hood to reach gets used once and then forgotten.

The cable detaches at the head, which keeps the motor serviceable inside a finished opening. Confirm the connector on the motor you receive before you order a replacement lead.

Confirm the tube inside diameter, count the turns of travel against the 34 turn limit capacity, then order the Somfy 540R2 CMO 120V 4-Wire Motor (1049026) with the crown and drive set that matches the tube. Somfy backs the motor for five years.

Frequently asked questions

What tube size does the Somfy 540R2 CMO fit?

Somfy publishes a minimum tube inside diameter of 1.85 inches for reference 1049026, with a motor body diameter of 1.77 inches. Any tube with a smaller inside diameter will not accept the motor. Match a crown and drive set to the tube profile, whether that tube is octagonal at 60 mm or 70 mm, 78 mm, or round at 2.5 inches.

How much torque does the 540R2 CMO produce?

The motor produces 40 Nm at 14 rpm. That figure covers heavy retractable awnings, aluminum rolling shutter curtains and tall exterior screens. Calculate the load from tube weight and roll diameter rather than from opening width, then leave headroom for a fabric that gains weight when it takes rain.

Does the 540R2 CMO work with Somfy remotes?

The motor holds no radio receiver, so a handheld remote cannot talk to it out of the box. It answers a maintained wall switch or a Somfy motor controller through its four wire cable. Add an RTS or Zigbee receiver on the supply side of the motor and remote, app and voice control all reach it.

Why choose a CMO head over a standard head?

CMO stands for compact manual override. The head accepts an eye rod so the owner can crank the awning or shutter by hand during a power outage. On an exterior application, that crank protects the fabric and the opening when weather arrives and the circuit is dead. A standard head offers no hand operation.

Shade Motors Direct is an authorized source for genuine Somfy motorized window shade, blind, and drapery parts.

Previous Post Next Post

Leave A Comment

Please note, comments need to be approved before they are published.

Welcome to our store
Welcome to our store
Welcome to our store